Cisco Systems 8900 User Manual

About This Guide  
This section desribes the audience, purpose, and organization of the Cisco MGX 8800/8900 Series  
Hardware Installation Guide. It also explains the conventions used to present information in this guide.  
Audience  
Purpose  
This guide is intended for use by installers, operators, network designers, and managers responsible for  
installing, configuring, or maintaining Cisco MGX switches or media gateways. These users should be  
familiar with telecommunications products and networking systems.  
This hardware installation guide describes how to set up and install the Cisco MGX 8850, Cisco MGX  
8850/B, Cisco MGX 8950, Cisco MGX 8830 and Cisco MGX 8830/B switches. It also describes how to  
setup and install the MGX 8880 Media Gateway.  
After completing the installation procedures covered in this guide, refer to the appropriate related  
documents to configure the switch or gateway. Refer to “Documentation” later in this preface for  
guidance on which documents to use.  
Organization  
This guide is organized as follows:  
Chapter 1, “Product Overviews,” provides an overview of the MGX switches, MGX media gateway,  
and their related components.  
Chapter 2, “Illustrated Card List for MGX Switches and the MGX 8880 Media Gateway,” provides  
an overview of all cards used in Cisco MGX switches and the MGX 8880 Media Gateway from  
MGX software Releases 2 through 5.1.  
Chapter 3, “Preparing for Installation,” lists site specifications and tools required for installing each  
switch or gateway and its related components.  
Chapter 4, “Planning for Card Redundancy, Line Redundancy, and Bulk Distribution,” describes  
how to plan for card redundancy, line redundancy, and bulk distribution.  
Chapter 5, “Installing the Cisco MGX Switch or Gateway,” contains procedures for installing each  
Cisco MGX chassis, whether in a rack or in a Cisco-supplied cabinet.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxiii  
Scope of this Guide  
Table 1  
Conventions Used in this Guide (continued)  
Convention  
{ }  
Definition  
Sample  
offset-list {in | out} offset  
Braces indicate a required choice.  
[{ }]  
Braces within a bracket indicate a required [{letter\number}Enter]  
choice within an optional element.  
Notes, Warnings, and Cautions  
This section explains the conventions used for notes, warnings, and cautions.  
Note  
A Note highlights helpful information, such as suggestions or references to material not covered in the  
guide.  
Tip  
Caution  
Warning  
A Tip contains information that might help you solve a problem or save time.  
A Caution emphasizes a situation in which equipment can be damaged or data can be corrupted or lost.  
A Warning emphasizes a safety concern, where a very serious and hazardous situation could result if  
instructions are not carefully adhered to.  
Notes about Warnings  
Warnings used in this document are translated into many languages in the Regulatory Compliance and  
Safety Information for Cisco Multiservice Switch Products (MGX, BPX, and SES).  
There are 3 types of Warnings in hardware guides:  
EMC (electromagnetic compatibility)  
Safety  
Telecom  
Warning statements are numbered. The numbering makes it clearer which Warning translation goes with  
which source Warning.  
Scope of this Guide  
This guide consolidates the following guides into one document and adds information about MGX  
Release 5 (and greater) hardware features. Thus, this guide covers all MGX switches supported by  
software Release 2.0 through 5.1, and makes the following guides obsolete:  
Cisco MGX 8850 Hardware Installation Guide, Release 2  
Cisco MGX 8850 Hardware Installation Guide, Release 2.1  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxv  
Scope of this Guide  
Cisco MGX 8950 Hardware Installation Guide, Release 2.1  
Cisco MGX 8850 (PXM45 and PXM1E) Hardware Installation Guide, Release 3  
Cisco MGX 8950 Hardware Installation Guide, Release 3  
Cisco MGX 8830 Hardware Installation Guide, Release 3  
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, and Cisco MGX 8830 Hardware Installation  
Guide, Releases 2 Through 4  
New Hardware Introduced in Releases 4.0.10 through 5.3  
This guide was updated to describe the modules and hardware introduced in MGX Releases 4.0.10  
through 5.1 (see Table 2).  
Table 2  
Hardware Introduced in Releases 4.0.10 or 5.3, by Chassis  
Hardware Introduced in MGX  
Release 4.0.10 through 5.1  
MGX 8850 MGX 8850 MGX  
MGX  
MGX 8830 8830/B  
MGX  
MGX 8950 8880  
(PXM1E)  
(PXM45)  
8850/B  
MGX 8880 Media Gateway  
MGX 8850/B  
x
x
x
x
x
MGX 8830/B  
AXSM-16-155-XG 16-port OC3  
Module with VSVD  
x
MGX8950-EXTDR-CONconnector —  
card  
x
RCON-IT05-8850 connector card1  
RCON-IT03-8850 connector card1  
RCON-IT03-8830 connector card1  
x
x
x
x
x
x
MGX-VXSM-4-155 Voice Switch  
Service Module (VXSM),  
4 OC3/STM-1  
MGX-VXSM-48T1E1 Voice Switch —  
Service Module (VXSM)  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
MPSM-8-T1E1Multiprotocol  
Service Module  
x
x
MPSM-T3E3-155 Multiprotocol  
Service Module  
x
x
x
MPSM-16-T1E1 Multiprotocol  
Service Module  
x
x
x
SRME/B Enhanced Service  
Resource Module  
x
x
x
MGX-VXSM-T3  
x
1. Pre-installed in chassis.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxvi  
   
Documentation  
New Back Cards Introduced in Releases 4.0.10 through 5.3  
The following back cards were introduced in MGX Releases 4.0.10 through 5.1:  
BNC-3-T3E3 3-port T3E3  
MCC-16-E1-1N  
MGX-2GE  
MGX-2OC12POS  
MGX-BNC-3T3-M  
MGX-STM1-EL-1  
RBBN-16-T1E1-1N  
RED-16-T1E1  
SFP-2-155  
SMB-2-155-EL  
VXSM-BC-3T3  
MGX-RJ45-5-ETH  
Documentation  
A Finding Cisco User Documentation Online document ships with your product. That guide contains  
general information about how to locate Cisco MGX, BPX, SES, and CWM documentation online.  
Documentation Notes for these Product Releases  
This release includes new hardware or features for the following releases:  
Cisco MGX Release 5.2 introduces the Cisco MGX 8850/B multiservice switch  
Cisco MGX Release 5.2, for these multiservice switches:  
Cisco MGX 8850 (PXM1E)  
Cisco MGX 8850 (PXM45)  
Cisco MGX 8950  
Cisco MGX 8830  
Cisco MGX Release 1.3, for these multiservice switches:  
Cisco MGX 8850 (PXM1)  
Cisco MGX 8230  
Cisco MGX 8250  
Cisco MGX Release 5.2, for the Route Processor Modules (RPM-XF and RPM-PR)  
Cisco WAN Manager Release 15.1. CWM Release 15 introduced a helpful new documentation  
feature: web-based online help. To invoke online help, press F1 on a PC, press the Help key on a  
UNIX workstation, or select Help from the main or popup menu. Cisco WAN Manager online help  
has been updated for Release 15.1.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxvii  
 
Documentation  
Other components of multiservice WAN products, such as the Service Expansion Shelf (SES) and WAN  
switching software have no new features for this release.  
Related Documentation  
This section describes the user guides and release notes that support this release of Cisco Multiservice  
Switch products.  
User Guide—Order of Use  
Use the guides listed here in the following order:  
Step 1  
Refer to the documents that ship with your product. Observe all safety precautions.  
Regulatory Compliance and Safety Information for Cisco Multiservice Switch Products (MGX, BPX,  
and SES)—This document familiarizes you with safety precautions for your product.  
Finding Cisco User Documentation Online—This document explains how to find documentation for  
MGX, BPX, and SES multiservice switches and media gateways as well as CWM network  
management software. These documents are available only online.  
Installation Warning Card—This document provides precautions about installing your cards. It  
explains such subjects as removing the shipping tab and inserting cards properly into the correct  
slots.  
Step 2  
Step 3  
Refer to the release notes for your product.  
If your network uses the CWM network management system, upgrade CWM. (If you are going to install  
CWM for the first time, do so after Step 4.) Upgrade instructions are included in the following  
documents:  
Cisco WAN Manager Installation Guide, Release 15.3.00  
Cisco WAN Manager User’s Guide, Release 15.3.00  
Step 4  
Step 5  
If your network contains MGX and SES products, refer to this guide for planning information:  
Cisco PNNI Network Planning Guide for MGX and SES Products  
Refer to these guides for information about installing cards and cables in the MGX chassis:  
Cisco MGX 8800/8900 Hardware Installation Guide, Releases 2 - 5.3 for installing cards and cables  
in these chassis.  
Cisco MGX 8xxx Edge Concentrator Installation and Configuration Guide for installing cards and  
cables in the Cisco MGX 8230, Cisco MGX 8250, or Cisco MGX 8850 (PXM1) chassis.  
Step 6  
Step 7  
Refer to the guides that help you configure your MGX switch and processor cards:  
Cisco MGX 8800/8900 Series Configuration Guide, Release 5.2 for these chassis.  
Cisco MGX 8xxx Edge Concentrator Installation and Configuration Guide for the Cisco MGX 8230,  
Cisco MGX 8250, or Cisco MGX 8850 (PXM1) chassis.  
Refer to the guide that supports the additional cards you intend to install in your switch. For example:  
Services guides can help you establish ATM, Frame Relay, or circuit emulation services on your  
switch.  
VISM guides can help you set up your switch as a voice gateway, and an RPM guide can help you  
implement IP on the switch.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxviii  
Documentation  
Step 8  
Note  
Additional guides, such as command reference guides and error message documentation, can help with  
the daily operation and maintenance of your switch.  
User guide titles may be different for earlier software releases. The titles shown in Table 3 are for the  
September 2005 release.  
User Guide Titles and Descriptions  
Table 3 lists the technical guides and release notes that support the September 2005 multiservice switch  
product releases. User documentation and release notes in Table 3 are listed in order of use and include  
information about which multiservice switch or media gateway the document supports.  
The Cisco MGX 8230, Cisco MGX 8250, and Cisco MGX 8850 (PXM1) switch documentation was not  
updated for the September 2005 release. Therefore, some information about configuring and using the  
new MPSM-8-T1E1 card in these switches is included in the following guides:  
Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration Guide and Command Reference for  
MGX Switches, Release 5.2  
Cisco Frame Relay Services (FRSM/MPSM-8-T1E1) Configuration Guide and Command Reference  
for MGX Switches, Release 5.2  
Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1) Configuration Guide and Command  
Reference for MGX Switches, Release 5.2  
Information about how to install or upgrade to the MPSM-8-T1E1 card in Cisco MGX 8230, Cisco  
MGX 8250, and Cisco MGX 8850 (PXM1) switches is in the Release Notes for Cisco MGX 8230, Cisco  
MGX 8250, and Cisco MGX 8850 (PXM1) Switches, Release 1.3.14.  
Note  
Refer to each product’s release notes for the latest information on features, bug fixes, and more.  
Terms  
Two main types of ATM cards are used in MGX switches: AXSM and AUSM. AXSM stands for ATM  
Switching Service Module. AUSM stands for ATM UNI (User Network Interface) Service Module.  
CWM stands for Cisco WAN Manager, our multiservice switch network management system.  
Legacy service module refers to a previously introduced card. For this release, the term is used  
specifically for the CESM-8-T1E1, FRSM-8-T1E1, and AUSM-8-T1E1 cards, which can now be  
replaced by the new MPSM-8-T1E1 card.  
MPSM stands for Multiprotocol Service Module.  
RPM stands for Route Processor Module.  
SES stands for Service Expansion Shelf.  
VISM stands for Voice Interworking Service Module.  
VXSM stands for Voice Switch Service Module.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xxxix  
Documentation  
Table 3  
User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways  
MGX  
8850  
MGX  
8850  
MGX  
8850  
BPX  
MGX  
MGX  
MGX  
MGX  
MGX  
with SES 8230 Rel. 8250 Rel. (PXM1)  
8830  
(PXM1E) (PXM45) 8950  
8880  
Document Title and Part Number  
Overview and Safety Documents  
Rel. 4  
1.3  
1.3  
Rel. 1.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3.  
Finding Cisco User Documentation  
Online  
x
x
x
x
x
x
x
x
x
DOC-7814807=  
Installation Warning Card  
DOC-7812348=  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Regulatory Compliance and Safety  
Information for Cisco Multiservice  
Switch Products (MGX, BPX, and  
SES)  
DOC-7814790=  
Release Notes for the Cisco MGX  
8880 Media Gateway, Release  
5.3.00  
x
x
x
x
x
OL-8892-01  
Release Notes for Cisco MGX 8850  
(PXM1E/PXM45), Cisco MGX  
8950, and Cisco MGX 8830  
Switches, Release 5.3.00  
OL-8891-01  
Release Notes for Cisco MGX 8230,  
Cisco MGX 8250, and Cisco MGX  
8850 (PXM1) Switches, Release  
1.3.14  
x
x
x
x
x
OL-8973-01  
Release Notes for the Cisco Voice  
Switch Service Module (VXSM),  
Release 5.3.00  
OL-10285-01  
Release Notes for Cisco WAN  
Manager, Release 15.3.00  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OL-10216-01  
Release Notes for the Cisco Voice  
Interworking Service Module  
(VISM), Release 3.3.25  
OL-8428-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xl  
 
Documentation  
Table 3  
User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)  
MGX  
8850  
MGX  
8850  
MGX  
8850  
BPX  
MGX  
MGX  
MGX  
MGX  
MGX  
with SES 8230 Rel. 8250 Rel. (PXM1)  
8830  
(PXM1E) (PXM45) 8950  
8880  
Document Title and Part Number  
Rel. 4  
1.3  
1.3  
Rel. 1.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3.  
Release Notes for Cisco MGX  
Route Processor Module (RPM-XF)  
IOS Release 12.4(6)T1 for  
PXM45-based Switches, Release  
5.3.00  
x
x
x
x
OL-8893-01  
Release Notes for Cisco MGX  
Route Processor Module (RPM-PR)  
IOS Release 12.4(6)T1 for MGX  
Releases 1.3.14 and 5.3.00  
x
x
x
x
x
x
x
x
OL-8894-01  
Cisco MGX 8230 Edge  
Concentrator Overview, Release  
1.1.31  
x
x
x
DOC-7812899=  
Cisco MGX 8250 Edge  
Concentrator Overview, Release  
1.1.31  
DOC-7811576=  
Cisco MGX 8850 Multiservice  
Switch Overview, Release 1.1.31  
OL-1154-01  
Hardware Installation Guides  
Cisco MGX 8800/8900 Hardware  
Installation Guide, Releases 2 - 5.3  
x
x
x
x
x
x
OL-4545-01  
Cisco Service Expansion Shelf  
Hardware Installation Guide,  
Release 11  
DOC-786122=  
Planning and Configuration Guides  
Cisco PNNI Network Planning  
Guide for MGX and SES Products  
x
x
x
x
x
x
x
x
x
x
x
OL-3847-01  
Cisco MGX 8800/8900 Series  
Configuration Guide, Release 5.2  
OL-6482-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xli  
Documentation  
Table 3  
User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)  
MGX  
8850  
MGX  
8850  
MGX  
8850  
BPX  
MGX  
MGX  
MGX  
MGX  
MGX  
with SES 8230 Rel. 8250 Rel. (PXM1)  
8830  
(PXM1E) (PXM45) 8950  
8880  
Document Title and Part Number  
Rel. 4  
1.3  
1.3  
Rel. 1.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3.  
Cisco WAN Manager Installation  
Guide, Release 15.3.00  
x
x
x
x
x
x
x
x
x
OL-10358-01  
Cisco WAN Manager User’s Guide,  
Release 15.3.00  
x
x
x
x
x
x
x
x
x
x
OL-10427-01  
Cisco MGX 8850 Edge  
Concentrator Installation and  
Configuration, Release 1.1.31  
DOC-7811223=  
Cisco SES PNNI Controller  
Software Configuration Guide,  
Release 31  
x
x
x
DOC-7814258=  
Cisco MGX 8230 Edge  
Concentrator Installation and  
Configuration, Release 1.1.31  
DOC-7811215=  
Cisco MGX 8250 Edge  
Concentrator Installation and  
Configuration, Release 1.1.31  
DOC-7811217=  
Service Module Configuration and Reference Guides  
Cisco MGX Route Processor  
x
x
x
x
Module (RPM-PR) Installation and  
Configuration Guide, Release 5.21  
OL-7349-01  
Frame Relay Software  
Configuration Guide and Command  
Reference for the Cisco MGX 8850  
FRSM12 Card, Release 31  
DOC-7810327=  
2
2
2
Cisco ATM Services  
x
x
x
(AUSM/MPSM-8-T1E1)  
Configuration Guide and Command  
Reference for MGX Switches,  
Release 5.22  
OL-6479-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlii  
Documentation  
Table 3  
User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)  
MGX  
8850  
MGX  
8850  
MGX  
8850  
BPX  
MGX  
MGX  
MGX  
MGX  
MGX  
with SES 8230 Rel. 8250 Rel. (PXM1)  
8830  
(PXM1E) (PXM45) 8950  
8880  
Document Title and Part Number  
Rel. 4  
1.3  
1.3  
Rel. 1.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3.  
2
2
2
Cisco Frame Relay Services  
(FRSM/MPSM-8-T1E1)  
Configuration Guide and Command  
Reference for MGX Switches,  
Release 5.22  
x
x
x
OL-6480-01  
2
2
2
Cisco Circuit Emulation Services  
(CESM/MPSM-8-T1E1)  
x
x
x
Configuration Guide and Command  
Reference for MGX Switches,  
Release 5.22  
OL-6481-01  
Cisco MGX Route Processor  
x
x
x
x
x
x
Module (RPM-XF) Installation and  
Configuration Guide, Release 5.21  
OL-6594-01  
Cisco ATM Services (AXSM)  
Configuration Guide and Command  
Reference for MGX Switches,  
Release 5.2  
OL-6484-01  
Cisco ATM and Frame Relay  
Services (MPSM-T3E3-155 and  
MPSM-16-T1E1) Configuration  
Guide and Command Reference for  
MGX Switches, Release 5.2  
x
x
OL-6487-01  
Cisco Voice Switch Services  
Configuration Guide for MGX  
Switches and Media Gateways,  
Release 5.3  
x
x
x
x
x
x
x
x
x
OL-10284-01  
Cisco Voice Interworking Services  
(VISM) Configuration Guide and  
Command Reference, Release 3.3  
OL-5358-01  
Reference Guides  
Cisco MGX 8230 Multiservice  
Gateway Error Messages, Release  
1.1.31  
x
DOC-78112113=  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xliii  
Documentation  
Table 3  
User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)  
MGX  
8850  
MGX  
8850  
MGX  
8850  
BPX  
MGX  
MGX  
MGX  
MGX  
MGX  
with SES 8230 Rel. 8250 Rel. (PXM1)  
8830  
(PXM1E) (PXM45) 8950  
8880  
Document Title and Part Number  
Rel. 4  
1.3  
1.3  
Rel. 1.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3  
Rel. 5.3.  
Cisco MGX 8230 Multiservice  
Gateway Command Reference,  
Release 1.1.31  
x
DOC-7811211=  
Cisco MGX 8250 Multiservice  
Gateway Command Reference,  
Release 1.1.31  
x
x
x
x
x
x
DOC-7811212=  
Cisco MGX 8250 Multiservice  
Gateway Error Messages, Release  
1.1.31  
DOC-7811216=  
Cisco MGX 8800 Series Switch  
Command Reference, Release  
1.1.31  
DOC-7811210=  
Cisco MGX 8800 Series Switch  
System Error Messages, Release  
1.1.31  
x
x
DOC-7811240=  
Cisco SES PNNI Controller  
x
x
x
x
x
x
Command Reference, Release 31  
DOC-7814260=  
Cisco MGX 8800/8900 Series  
Command Reference, Release 5.2  
OL-6483-01  
Cisco Voice Switch Services  
Command Reference for MGX  
Switches and Media Gateways,  
Release 5.3  
x
x
OL-10283-01  
Cisco WAN Manager SNMP Service  
Agent, Release 15.3.00  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OL-10190-01  
Cisco WAN Manager Database  
Interface Guide, Release 15.3.00  
OL-10140-01  
1. This document was not updated for the September 2005 release.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xliv  
Documentation  
2. Some configuration and command information is included in this guide for using the multiprotocol service module (MPSM-8-T1E1/MPSM-16-T1E1) in  
a Cisco MGX 8230, MGX 8250, or MGX 8850 (PXM1) switch.  
Note  
For the September 2005 product release, there are no new features for the Service Expansion Shelf (SES)  
of the BPX switch and BPX WAN switching software. Therefore, documentation for these items was not  
updated. Table 3 lists the most recent user guides and release notes for these products.  
Table 3 also lists the latest documentation available for the Cisco MGX 8230, Cisco MGX 8250, and  
Cisco MGX 8850 (PXM1) switches. These switches use the PXM1 processor card. Although there are  
new features in MGX Release 1.3 for these switches, only the release notes were updated. And the  
following guides contain some information about configuring the MPSM-8-T1E1 and MPSM-16-T1E1  
cards for use in these switches:  
Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1) Configuration Guide and Command  
Reference for MGX Switches, Release 5.2  
Cisco Frame Relay Services (FRSM/MPSM-8-T1E1) Configuration Guide and Command Reference  
for MGX Switches, Release 5.2  
Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration Guide and Command Reference for  
MGX Switches, Release 5.2  
Table 4 lists the documents that ship with product.  
Table 5 contains alphabetized titles and descriptions of all the guides and release notes listed in Table 3.  
Table 4  
Documents that Ship with Multiservice Switch Products  
Document Title  
Description  
Finding Cisco User Documentation Online  
DOC-7817081=  
Describes how to find the guides and release notes that support  
multiservice switches and network management products.  
These documents are available only online. This guide ships  
with product.  
Installation Warning Card  
Contains precautions that you should take before you  
insert a card into a slot. This Warning Card ships with  
product.  
DOC-7812348=  
Regulatory Compliance and Safety Information for Cisco  
Multiservice Switch Products (MGX, BPX, and SES)  
Provides regulatory compliance information, product  
warnings, and safety recommendations for all the Cisco MGX  
multiservice switches: MGX 8230, MGX 8250, MGX 8850  
(PXM1), MGX 8850 (PXM45), MGX 8850 (PXM1E), MGX  
8830 and MGX 8950. Also provides such information for the  
MGX 8880 Media Gateway. This guide ships with product.  
DOC-7814790=  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlv  
 
Documentation  
Table 5  
User Guides and Release Notes for Cisco Multiservice Switch Products  
Document Title  
Description  
Cisco ATM and Frame Relay Services (MPSM-T3E3-155 and Provides software configuration procedures for provisioning  
MPSM-16-T1E1) Configuration Guide and Command  
Reference for MGX Switches, Release 5.2  
ATM and Frame Relay connections on the new  
MPSM-T3E3-155 multiprotocol service module. Also  
describes all MPSM-T3E3-155 commands.  
OL-6487-01  
Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration  
Provides software configuration procedures for provisioning  
Guide and Command Reference for MGX Switches, Release connections and managing the AUSM cards supported in this  
5.2  
release. Also describes all AUSM commands. Includes  
software configuration procedures for provisioning  
connections and managing the MPSM-8-T1E1 card as an  
AUSM card replacement.  
OL-6479-01  
Cisco ATM Services (AXSM) Configuration Guide and  
Command Reference for MGX Switches, Release 5.2  
Explains how to configure the AXSM cards and provides a  
command reference that describes the AXSM commands in  
detail. The AXSM cards covered in this guide are the  
AXSM-XG, AXSM/A, AXSM/B, AXSM-E, and  
AXSM-32-T1E1-E.  
OL-4548-01  
Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1)  
Configuration Guide and Command Reference for MGX  
Switches, Release 5.2  
Provides software configuration procedures for provisioning  
connections and managing the Circuit Emulation Service  
Module (CESM) cards supported in this release. Also  
describes all CESM commands. Includes software  
configuration procedures for provisioning connections and  
managing the MPSM-8-T1E1 card as a CESM card  
replacement.  
OL-6481-01  
Cisco Frame Relay Services (FRSM/MPSM-8-T1E1)  
Configuration Guide and Command Reference for MGX  
Switches, Release 5.2  
Provides software configuration procedures for provisioning  
connections and managing the Frame Relay Service Module  
(FRSM) cards supported in this release. Also describes all  
FRSM commands. Includes software configuration  
procedures for provisioning connections and managing the  
MPSM-8-T1E1 card as an FRSM card replacement.  
OL-6480-01  
Cisco MGX 8230 Edge Concentrator Installation and  
Configuration, Release 1.1.3  
Provides installation instructions for the Cisco MGX 8230  
edge concentrator.  
DOC-7811215=  
Cisco MGX 8230 Edge Concentrator Overview, Release 1.1.3 Describes the system components and function of the  
Cisco MGX 8250 edge concentrator.  
DOC-7812899=  
Cisco MGX 8230 Multiservice Gateway Command Reference, Provides detailed information on the general command line  
Release 1.1.3  
interface commands.  
DOC-7811211=  
Cisco MGX 8230 Multiservice Gateway Error Messages,  
Release 1.1.3  
Provides error message descriptions and recovery  
procedures.  
DOC-78112113=  
Cisco MGX 8250 Edge Concentrator Installation and  
Configuration, Release 1.1.3  
Provides installation instructions for the Cisco MGX 8250  
edge concentrator.  
DOC-7811217=  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlvi  
 
Documentation  
Table 5  
User Guides and Release Notes for Cisco Multiservice Switch Products (continued)  
Description  
Document Title  
Cisco MGX 8250 Edge Concentrator Overview, Release 1.1.3 Describes the system components and function of the  
Cisco MGX 8250 edge concentrator.  
DOC-7811576=  
Cisco MGX 8250 Multiservice Gateway Command Reference, Provides detailed information on the general command line  
Release 1.1.3  
interface commands.  
DOC-7811212=  
Cisco MGX 8250 Multiservice Gateway Error Messages,  
Release 1.1.3  
Provides error message descriptions and recovery  
procedures.  
DOC-7811216=  
Cisco MGX 8800 Series Switch Command Reference, Release Provides detailed information on the general command line  
1.1.3  
for the Cisco MGX 8850 (PXM1), Cisco MGX 8250, and  
Cisco MGX 8230 edge concentrators.  
DOC-7811210=  
Cisco MGX 8800 Series Switch System Error Messages,  
Release 1.1.3  
Provides error message descriptions and recovery procedures  
for Cisco MGX 8850 (PXM1), Cisco MGX 8250, and  
Cisco MGX 8230 edge concentrators.  
DOC-7811240=  
Cisco MGX 8800/8900 Hardware Installation Guide,  
Releases 2 - 5.3  
Describes how to install the Cisco MGX 8950, the  
Cisco MGX 8850 (PXM1E/PXM45), the Cisco MGX  
8850/B (PXM1E/PXM45), and the Cisco MGX 8830  
switches. Also describes how to install the MGX 8880 Media  
Gateway. This document explains what each switch does and  
covers site preparation, grounding, safety, card installation,  
and cabling. The Cisco MGX 8850 switch uses either a  
PXM45 or a PXM1E controller card and provides support for  
both serial bus-based and cell bus-based service modules.  
The Cisco MGX 8830 switch uses a PXM1E controller card  
and supports cell bus-based service modules. The Cisco  
MGX 8950 supports only serial bus-based service modules.  
The Cisco MGX 8880 uses a PXM45/C controller card, and  
supports only serial bus-based service modules. This  
hardware installation guide replaces all previous hardware  
guides for these switches.  
OL-4545-01  
Cisco MGX 8800/8900 Series Configuration Guide, Release Describes how to configure the Cisco MGX 8880 Media  
5.2  
Gateway. Also describes how to configure Cisco MGX 8850  
(PXM1E), Cisco MGX 8850 (PXM45), the Cisco MGX  
8850/B (PXM1E/PXM45), and Cisco MGX 8830 switches to  
operate as ATM edge switches and the Cisco MGX 8950  
switch to operate as a core switch. This guide also provides  
some operation and maintenance procedures.  
OL-6482-01  
Cisco MGX 8800/8900 Series Command Reference, Release Describes the PXM commands that are available in the CLI  
5.2  
of the Cisco MGX 8850 (PXM45), Cisco MGX 8850  
(PXM1E), Cisco MGX 8950, and Cisco MGX 8830 switches.  
Also describes the PXM commands that are available in the  
CLI of the Cisco MGX 8880 Media Gateway.  
OL-6483-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlvii  
Documentation  
Table 5  
User Guides and Release Notes for Cisco Multiservice Switch Products (continued)  
Document Title  
Description  
Cisco MGX 8850 Edge Concentrator Installation and  
Configuration, Release 1.1.3  
Provides installation instructions for the Cisco MGX 8850  
(PXM1) edge concentrator.  
DOC-7811223=  
Cisco MGX 8850 Multiservice Switch Overview, Release 1.1.3 Describes the system components and function of the  
Cisco MGX 8850 (PXM1) edge concentrator.  
OL-1154-01  
Cisco MGX and Service Expansion Shelf Error Messages,  
Release 5.0  
Provides error message descriptions and recovery  
procedures.  
OL-6485-01  
Cisco MGX Route Processor Module (RPM-XF) Installation Describes how to install and configure the Cisco MGX Route  
and Configuration Guide, Release 5.2  
Processor Module (RPM-XF) in the Cisco MGX 8850  
(PXM45), Cisco MGX 8880 (PXM45), and Cisco MGX 8950  
switch. Also provides site preparation procedures,  
troubleshooting procedures, maintenance procedures, cable  
and connector specifications, and basic Cisco IOS  
configuration information.  
OL-6954-01  
Cisco MGX Route Processor Module (RPM-PR) Installation Describes how to install and configure the Cisco MGX Route  
and Configuration Guide, Release 5.2  
Processor Module (RPM/B or RPM-PR) in the  
Cisco MGX 8850 (PXM1), the Cisco MGX 8250, and the  
Cisco MGX 8230 edge concentrators. Also provides site  
preparation procedures, troubleshooting procedures,  
maintenance procedures, cable and connector specifications,  
and basic Cisco IOS configuration information.  
OL-7349-01  
Cisco PNNI Network Planning Guide for MGX and SES  
Products  
Provides guidelines for planning a PNNI network that uses  
Cisco MGX 8830, Cisco MGX 8850 (PXM45 and PXM1E),  
Cisco MGX 8950, or Cisco BPX 8600 switches or the  
MGX 8880 Media Gateway. When connected to a PNNI  
network, each Cisco BPX 8600 Series switch requires an SES  
for PNNI route processing.  
OL-3847-01  
Cisco Service Expansion Shelf Hardware Installation Guide, Provides instructions for installing and maintaining an SES  
Release 1  
controller.  
DOC-786122=  
Cisco SES PNNI Controller Command Reference, Release 3 Describes the commands used to configure and operate the  
SES PNNI controller.  
DOC-7814260=  
Cisco SES PNNI Controller Software Configuration Guide,  
Release 3  
Describes how to configure, operate, and maintain the SES  
PNNI controller.  
DOC-7814258=  
Cisco Voice Interworking Services (VISM) Configuration  
Guide and Command Reference, Release 3.3  
Describes how to install and configure the Voice  
Interworking Service Module (VISM) in the Cisco  
MGX 8830, Cisco MGX 8850 (PXM45), and Cisco MGX  
8850 (PXM1E) multiservice switches. Provides site  
preparation procedures, troubleshooting procedures,  
maintenance procedures, cable and connector specifications,  
and Cisco CLI configuration information.  
OL-5358-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlviii  
Documentation  
Table 5  
User Guides and Release Notes for Cisco Multiservice Switch Products (continued)  
Document Title  
Description  
Cisco Voice Switch Services (VXSM) Configuration and  
Command Reference Guide for MGX Switches, Release 5  
Describes the features and functions of the new Voice Switch  
Service Module (VXSM) in the Cisco MGX 8880 Media  
Gateway and in the Cisco MGX8850 (PXM45 and PXM1E)  
multiservice switches. Also provides configuration  
procedures, troubleshooting procedures, and Cisco CLI  
configuration information.  
OL-4625-01  
Cisco WAN Manager Database Interface Guide, Release  
15.3.00  
Provides information about accessing the CWM Informix  
database that is used to store information about the network  
elements.  
OL-6261-01  
Cisco WAN Manager Installation Guide, Release 15.3.00  
Provides procedures for installing Release 15.1 of the CWM  
network management system.  
OL-6259-01  
Cisco WAN Manager SNMP Service Agent, Release 15.3.00 Provides information about the CWM Simple Network  
Management Protocol service agent, an optional adjunct to  
CWM that is used for managing Cisco WAN switches  
through SNMP.  
OL-6260-01  
Cisco WAN Manager User’s Guide, Release 15.3.00  
Describes how to use the CWM Release 15.1 software, which  
consists of user applications and tools for network  
management, connection management, network  
OL-6257-01  
configuration, statistics collection, and security management.  
Note  
The CWM interface now has built-in documentation  
support in the form of online Help. On a PC, press F1  
to access Help; on a UNIX workstation, press the  
Help key. Alternatively, on either system you can  
select Help from the main or popup menu.  
Frame Relay Software Configuration Guide and Command  
Describes how to use the high-speed Frame Relay  
Reference for the Cisco MGX 8850 FRSM12 Card, Release 3 (FRSM-12-T3E3) commands that are available in the CLI of  
the Cisco MGX 8850 (PXM45) switch.  
DOC-7810327=  
Release Notes for Cisco MGX 8230, Cisco MGX 8250, and  
Cisco MGX 8850 (PXM1) Switches, Release 1.3.14  
Provides new feature, upgrade, and compatibility  
information, as well as information about known and  
resolved anomalies.  
OL-4539-01  
Release Notes for Cisco MGX 8850 (PXM1E/PXM45), Cisco Provides new feature, upgrade, and compatibility  
MGX 8950, and Cisco MGX 8830 Switches, Release 5.3.00  
information, as well as information about known and  
resolved anomalies.  
OL-6478-01  
Release Notes for the Cisco MGX 8880 Media Gateway,  
Release 5.3.00  
Provides new feature and compatibility information, as well  
as information about known and resolved anomalies.  
OL-6493-01  
Release Notes for Cisco MGX Route Processor Module  
Provides upgrade and compatibility information, as well as  
(RPM-PR) IOS Release 12.4(6)T1 for MGX Releases 1.3.14 information about known and resolved anomalies.  
and 5.3.00  
OL-7292-01  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
xlix  
Obtaining Documentation  
Table 5  
User Guides and Release Notes for Cisco Multiservice Switch Products (continued)  
Document Title  
Description  
Release Notes for Cisco MGX Route Processor Module  
Provides upgrade and compatibility information, as well as  
(RPM-XF) IOS Release 12.4(6)T1 for PXM45-based Switches, information about known and resolved anomalies.  
Release 5.3.00  
OL-7059-01  
Release Notes for the Cisco Voice Interworking Service  
Module (VISM), Release 3.3.25  
Provides new feature, upgrade, and compatibility  
information, as well as information about known and  
resolved anomalies.  
OL-5357-01  
Release Notes for the Cisco Voice Switch Service Module  
(VXSM), Release 5.3.00  
Provides new feature, upgrade, and compatibility  
information, as well as information about known and  
resolved anomalies.  
OL-7088-01  
Release Notes for Cisco WAN Manager, Release 15.3.00  
Provides new feature, upgrade, and compatibility  
information, as well as information about known and  
resolved anomalies.  
OL-6495-01  
Obtaining Documentation  
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several  
ways to obtain technical assistance and other technical resources. These sections explain how to obtain  
technical information from Cisco Systems.  
Cisco.com  
You can access the most current Cisco documentation at this URL:  
You can access the Cisco website at this URL:  
You can access international Cisco websites at this URL:  
Product Documentation DVD  
The Product Documentation DVD is a comprehensive library of technical product documentation on a  
portable medium. The DVD enables you to access multiple versions of installation, configuration, and  
command guides for Cisco hardware and software products. With the DVD, you have access to the same  
HTML documentation that is found on the Cisco website without being connected to the Internet.  
Certain products also have .PDF versions of the documentation available.  
The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com  
users (Cisco direct customers) can order a Product Documentation DVD (product number  
DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at this URL:  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
l
Documentation Feedback  
Ordering Documentation  
Registered Cisco.com users may order Cisco documentation at the Product Documentation Store in the  
Cisco Marketplace at this URL:  
Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.  
(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by  
calling 011 408 519-5055. You can also order documentation by e-mail at  
tech-doc-store-mkpl@external.cisco.com or by fax at 1 408 519-5001 in the United States and Canada,  
or elsewhere at 011 408 519-5001.  
Documentation Feedback  
You can rate and provide feedback about Cisco technical documents by completing the online feedback  
form that appears with the technical documents on Cisco.com.  
You can submit comments about Cisco documentation by using the response card (if present) behind the  
front cover of your document or by writing to the following address:  
Cisco Systems  
Attn: Customer Document Ordering  
170 West Tasman Drive  
San Jose, CA 95134-9883  
We appreciate your comments.  
Cisco Product Security Overview  
Cisco provides a free online Security Vulnerability Policy portal at this URL:  
From this site, you will find information about how to:  
Report security vulnerabilities in Cisco products.  
Obtain assistance with security incidents that involve Cisco products.  
Register to receive security information from Cisco.  
A current list of security advisories, security notices, and security responses for Cisco products is  
available at this URL:  
To see security advisories, security notices, and security responses as they are updated in real time, you  
can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS)  
feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
li  
Obtaining Technical Assistance  
Reporting Security Problems in Cisco Products  
Cisco is committed to delivering secure products. We test our products internally before we release them,  
and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability  
in a Cisco product, contact PSIRT:  
For Emergencies onlysecurity-alert@cisco.com  
An emergency is either a condition in which a system is under active attack or a condition for which  
a severe and urgent security vulnerability should be reported. All other conditions are considered  
nonemergencies.  
For Nonemergenciespsirt@cisco.com  
In an emergency, you can also reach PSIRT by telephone:  
1 877 228-7302  
1 408 525-6532  
Tip  
We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to  
encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been  
encrypted with PGP versions 2.x through 9.x.  
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence  
with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page  
at this URL:  
The link on this page has the current PGP key ID in use.  
If you do not have or use PGP, contact PSIRT at the aforementioned e-mail addresses or phone numbers  
before sending any sensitive material to find other means of encrypting the data.  
Obtaining Technical Assistance  
Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco  
Technical Support & Documentation website on Cisco.com features extensive online support resources.  
In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)  
engineers provide telephone support. If you do not have a valid Cisco service contract, contact your  
reseller.  
Cisco Technical Support & Documentation Website  
The Cisco Technical Support & Documentation website provides online documents and tools for  
troubleshooting and resolving technical issues with Cisco products and technologies. The website is  
available 24 hours a day, at this URL:  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
lii  
Obtaining Technical Assistance  
Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user  
ID and password. If you have a valid service contract but do not have a user ID or password, you can  
register at this URL:  
Note  
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting  
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &  
Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose  
Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco  
Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by  
product ID or model name; by tree view; or for certain products, by copying and pasting show command  
output. Search results show an illustration of your product with the serial number label location  
highlighted. Locate the serial number label on your product and record the information before placing a  
service call.  
Submitting a Service Request  
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3  
and S4 service requests are those in which your network is minimally impaired or for which you require  
product information.) After you describe your situation, the TAC Service Request Tool provides  
recommended solutions. If your issue is not resolved using the recommended resources, your service  
request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:  
For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.  
(S1 or S2 service requests are those in which your production network is down or severely degraded.)  
Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business  
operations running smoothly.  
To open a service request by telephone, use one of the following numbers:  
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)  
EMEA: +32 2 704 55 55  
USA: 1 800 553-2447  
For a complete list of Cisco TAC contacts, go to this URL:  
Definitions of Service Request Severity  
To ensure that all service requests are reported in a standard format, Cisco has established severity  
definitions.  
Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations.  
You and Cisco will commit all necessary resources around the clock to resolve the situation.  
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your  
business operations are negatively affected by inadequate performance of Cisco products. You and Cisco  
will commit full-time resources during normal business hours to resolve the situation.  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
liii  
Obtaining Additional Publications and Information  
Severity 3 (S3)—Operational performance of the network is impaired, while most business operations  
remain functional. You and Cisco will commit resources during normal business hours to restore service  
to satisfactory levels.  
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or  
configuration. There is little or no effect on your business operations.  
Obtaining Additional Publications and Information  
Information about Cisco products, technologies, and network solutions is available from various online  
and printed sources.  
The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief  
product overviews, key features, sample part numbers, and abbreviated technical specifications for  
many Cisco products that are sold through channel partners. It is updated twice a year and includes  
the latest Cisco offerings. To order and find out more about the Cisco Product Quick Reference  
Guide, go to this URL:  
Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo  
merchandise. Visit Cisco Marketplace, the company store, at this URL:  
Cisco Press publishes a wide range of general networking, training and certification titles. Both new  
and experienced users will benefit from these publications. For current Cisco Press titles and other  
information, go to Cisco Press at this URL:  
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and  
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,  
technology breakthroughs, and Cisco products and solutions, as well as network deployment and  
troubleshooting tips, configuration examples, customer case studies, certification and training  
information, and links to scores of in-depth online resources. You can access Packet magazine at  
this URL:  
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies  
learn how they can use technology to increase revenue, streamline their business, and expand  
services. The publication identifies the challenges facing these companies and the technologies to  
help solve them, using real-world case studies and business strategies to help readers make sound  
technology investment decisions. You can access iQ Magazine at this URL:  
or view the digital edition at this URL:  
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering  
professionals involved in designing, developing, and operating public and private internets and  
intranets. You can access the Internet Protocol Journal at this URL:  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
liv  
Obtaining Additional Publications and Information  
Networking products offered by Cisco Systems, as well as customer support services, can be  
obtained at this URL:  
Networking Professionals Connection is an interactive website for networking professionals to share  
questions, suggestions, and information about networking products and technologies with Cisco  
experts and other networking professionals. Join a discussion at this URL:  
World-class networking training is available from Cisco. You can view current offerings at  
this URL:  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
lv  
Obtaining Additional Publications and Information  
Cisco MGX 8800/8900 Series Hardware Installation Guide  
Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006  
lvi  

HP Hewlett Packard HP Widescreen LCD Monitor 2310 User Manual
HP Hewlett Packard Hewlett Packard Computer Monitor V185WS User Manual
Frigidaire FFGC3603LW User Manual
Frigidaire CFEF3048LS User Manual
Eizo EIZO FlexScan F57 User Manual
BT FREELANCE XA 2000 User Manual
AT T 7625 User Manual
Asus Computer Monitor ML249 User Manual
AOC Widescreen Lcd Monitor E2251FWU User Manual
Ampro Corporation COM 830 User Manual